DESIGN VARIATION Content length & block density:
Quick Decoder · 3 Formula Stat Cards + Core Tip Chart Standard Guide · + SA3 Tip Anatomy + Guard Compatibility Table Complete Technical Reference · SA2 Sticky Jump Bar + Full Chart + Hotspots + Compatibility + Accordion + A6 Picks
Home › Sprayers › Spray Tips › Tip Size Decoder

Graco Spray Tip Size Chart Explained (310, 415, 515)

How to decode any 3-digit airless spray tip number in five seconds, match orifice size to your pump rating, and pick the right gun filter mesh.

How to read the 3-digit number

FAN WIDTH FORMULA
Digit 1 × 2
At 12" distance (515 = 10" fan)
ORIFICE FORMULA
Digits 2–3
Thousandths of an inch (515 = .015")
FILTER RULE
100 vs 60
100-mesh for .008–.012", 60-mesh for .015"+

Every reversible airless spray tip—whether Graco, Titan, or Wagner—uses the same industry-standard 3-digit code. Take a 515 tip: multiply the first digit (5) by two to get a 10-inch fan width when held 12 inches from the wall. The last two digits (15) mean a 0.015-inch hole drilled into the tungsten carbide core.

Master Graco spray tip size & filter chart

Match your coating thickness to the orifice size first, then pick fan width based on surface width.

TIP CODEFAN WIDTH (12")ORIFICE (IN)MAX FLOW (GPM)BEST COATING & SURFACEGUN FILTERMIN PUMP
208 / 210 4 in 0.008"–0.010" 0.09 GPM Wood stains, clear poly, narrow window sash 100 mesh (Blue) Any airless
310 FFLP 6 in 0.010" 0.11 GPM Kitchen cabinet doors & drawers 100 mesh (Blue) Magnum X5+
312 FFLP 6 in 0.012" 0.15 GPM Baseboards, casings & crown trim 100 mesh (Blue) Magnum X5+
413 8 in 0.013" 0.18 GPM 6-panel interior doors, built-in bookcases 100 mesh (Blue) Magnum X5+
415 8 in 0.015" 0.24 GPM Small bedrooms, hallways, PVA drywall primer 60 mesh (Black) Magnum X5+
515 10 in 0.015" 0.24 GPM Living room walls, ceilings, siding 60 mesh (Black) Magnum X5+
517 10 in 0.017" 0.31 GPM Thick exterior latex, stucco, fences 60 mesh (Black) Magnum X7 / Pro
519 / 521 10 in 0.019"–0.021" 0.41 GPM Elastomeric masonry coatings, block filler 30 mesh (Grey) Pro 395+ only
Green FFLP tips require the blue RAC X HandTite guard (part #246215).
ADVERTISEMENT
TIP ANATOMY · 4 PARTS

Inside a reversible airless tip & guard assembly

diagram · RAC X reversible tip, OneSeal gasket, and HandTite guard
1
2
3
4
1
Color-Coded Wing Paddle

Green = FFLP (Fine Finish Low Pressure); Blue = LP (Low Pressure walls); Black = Standard RAC X.

2
3-Digit Stamped Code (e.g. 310)

First digit × 2 = fan width in inches; last two digits = tungsten hole diameter in thousandths.

3
Reversible Stainless Barrel

Rotates 180° from SPRAY position (arrow forward) to UNCLOG position (arrow backward).

4
OneSeal Solvent Gasket

Seats inside the RAC X guard nose to seal 3,000 PSI without requiring a wrench.

Tip guard & filter compatibility

PART / TIP SERIES FITS GUARD / GUN CRITICAL FIT NOTE
Green RAC X FFLP Tips (310, 312, 414) Blue RAC X HandTite Guard (7/8" thread) Does NOT fit older black RAC V guards
Black RAC V Tips (standard box tip) Black or Orange RAC V Guard Included in the box with Graco Magnum X5/X7
Blue 100-Mesh Gun Filter SG2, SG3, and Contractor PC guns Mandatory for 210, 310, and 312 tips
12"–15" Tip Extension Wand Any 7/8" airless gun thread Saves ladder moves on 9-foot ceilings & decks

Common spray tip & guard problems

SYMPTOM WHY IT HAPPENS QUICK FIX
Tip clogs every 60 seconds on cabinet doors Running a 0.010" (310) tip with the factory 60-mesh coarse filter still inside the gun handle. Swap to a blue 100-mesh gun filter and strain the enamel through a nylon cone bag before inserting the siphon tube.

Swap to a blue 100-mesh gun filter and strain the enamel through a nylon cone bag before inserting the siphon tube.

Paint leaks around the plastic tip wing The internal metal-and-rubber OneSeal gasket fell out or was installed backward. Use the pointed nose of the tip to align the curved saddle of the OneSeal gasket inside the RAC X guard, then tighten the guard collar firmly by hand.

Use the pointed nose of the tip to align the curved saddle of the OneSeal gasket inside the RAC X guard, then tighten the guard collar firmly by hand.

Green FFLP tip won’t slide into my guard Trying to insert a larger-barrel RAC X tip into the stock black RAC V guard. Replace the black guard with a Graco RAC X HandTite Blue Guard (part #246215).

Replace the black guard with a Graco RAC X HandTite Blue Guard (part #246215).

Frequently asked questions

What is the difference between a 310 and a 410 spray tip?

Both have the exact same 0.010-inch hole and spray the exact same amount of paint per minute (0.11 GPM). The 310 spreads that paint across a narrower 6-inch fan (putting down a slightly thicker wet film per pass), while the 410 spreads the same volume across an 8-inch fan.

How do I know if my airless pump is big enough for a 517 tip?

Check the "Max Tip Size" spec on your sprayer’s serial plate. A Graco Magnum X5 is rated up to a 0.015" tip (so 415 or 515 is its ceiling). A Graco Magnum X7 is rated up to a 0.017" tip (517).

EVERY SUNDAY

The Sunday Coat

One pro painting technique, one prep fix, one good read. Every Sunday.